The typical life of a furnace filter is 3 months. This can vary based on how much the fan is running, how dirty the ducts are, and the lifestyle of the tenant/homeowners. Pet hair and dander can be a significant factor as well. The best way to gauge how often the furnace filter needs to be changed is to check it often and see how dirty it gets.
You should never let the filter get to the point when you hold it up to the light and only 50% of the light is visible looking through the filter.
A good rule of thumb if you live in Denver, CO is to replace the filter in the fall when the furnace first starts running a fair amount. Replace it again at the end of January and if you forget to check it again at least you are changing it twice a year and this should be good enough to make sure it is pretty clean. If you have a two stage high efficiency furnace the fan will tend to run more often so you may want to change it January first and again in Mid March.
If you have central air conditioning, then it’s a good idea to check the filter monthly in the summer to make sure it is clean. Changing every 2-3 months is usually sufficient.
It is more important to check and replace the filter than to pay extra for an expensive filter you only change once a year. Having a clean filter will extend the life of your furnace and can save you a significant amount of money by following a maintenance schedule.
Is your furnace not starting up and maybe making a funny sound like it is trying to start up? Perhaps you have shut it off and then turned back on. Maybe you just turned the fan on and it works. You may be in need of a new induced draft motor or draft inducer motor. This motor is what creates a draft through the heat exchanger. Air and gas are drawn through the front of the furnace and conveyed to the flue connector. What you have is a whole assembly. In most cases the entire assembly is what gets replaced. In some rare cases you can replace just the motor which is cheaper but takes longer to do. When replacing the assembly it is important to replace the gasket that goes between the assembly and the heat exchanger manifold. The gasket is usually fiberglass or fire rated foam. Modern furnaces have this motor as well the circulating or blower motor. Out of the 2 motors, the inducer motor typically is the one that fails first. The bearings start to wear out making the operation noisier and eventually they fail and the motor stops turning. I have seen motors with noisy bearings run for a long time (years) and in other cases no increased noise is noticed before the motor fails.
The induced draft assembly is typically made of steel or metals such as the one in the picture.
They often develop rust and wear out. Replacing the draft inducer motor assembly is the only way your furnace will operate.
How much should I expect to pay to replace my draft inducer motor assembly?
Depending on the make and model expect to pay between $500 and $800 for residential gas furnaces. At Tobin you can count on us to tell you what the problem is and give you a fair reasonable price ti install a new draft induced motor.
Give us a call for a quote if you are in the Denver Metro area 303.893.5675
Awarded for Excellence in Customer Service and superior product offerings.
TOBIN employs master technicians who are highly trained in their profession and are capable of performing their work at an entirely higher level than most technicians. Our technicians receive ongoing training, and are qualiﬁed to repair all major brands and models of furnaces and air conditioners. Plus, We have always been family owned and operated since 1954. You will be happy you gave us a call as we have great customer service and pricing that can not be beat. Of course we guarantee all of our work and our products.
A two stage furnace has 2 separate firing rates with the lower one operating at about 40% of the full rate. When your furnace kicks in it will start at the lower more efficient rate for 5 to 10 minutes. If your heat has not warmed up to where it was set during this time then the burner will switch to the higher firing rate to meet your heating needs. The 2 stage system is more efficient than a 1 stage furnace as the lower firing rate provides a better overall temperature by running the furnace more often at the lower rate. Thus, air is circulated more frequently which provides a more balanced room temperature throughout the home.
In many cases an upgrade from a basic 80% efficient furnace to a 2 stage is not a significant cost upgrade, usually around $300. These furnaces control the staging independent of the thermostat which works in most cases when people are not setting their set point back significantly. If you do set the temperature back to save energy it is better to upgrade to a furnace that the staging is controlled by the thermostat. These furnaces typically cost $600-800 more. In order to make it a true 2 stage, a 2 stage thermostat and additional wires need to be run. In cases when additional wires cannot be run there are thermostats available that although they are more expensive they can perform the furnace control over just 2 wires. There are also wireless thermostats that do the same they just are not wi fi capable.
The reason you need a 2 stage thermostat to control the staging is because when you set the thermostat back more than 3 degrees you want the furnace to fire in high stage to make up the 3 degrees quickly.
Most of the time your furnace is set to hold a given temperature for a long time for instance at night when you are sleeping. In this case, when the furnace gets a call for heat it only needs to make up a 1/2 to 1 degree and this is when the furnace will be in the low or first stage and give you longer run times for more even heating.
"TOBIN recently replaced two 27 year old furnaces in my house. They did a fantastic job in both planning the job and installing the furnaces. They were very professional, worked very cleanly and cared about getting the installation perfect. When they answered my numerous questions, you could tell they answered with a wealth of experience and knowledge. This is a great company you can trust."
- Brian Thomas
"Great Service. My furnace was short-cycleing and would shut off right after it turned on. They came really quickly, cleaned the parts and didn't charge me more then the service fee. They were very professional and nice. A really good family owned company. I would highly recommend."
- Brie Cook
"My furnace went out and I called up TOBIN to get an estimate. I had three other estimates for similar furnaces and the other companies wanted $1000 more. I hired TOBIN and had a high efficiency Amana furnace installed for much less than the other companies. I was very happy with the two service technicians who came out. They had to do some additional piping to vent the furnace and everything looked neat and clean when they were finished. I highly recommend the professionals at TOBIN."
- Bryan Murphy
TOBIN Heating & Airconditioning is the Denver's Most Trusted & Affordable Heating & Air Conditioning Service Since 1954 – Family Owned And Operated.